Victaulic Catalog
Pipe Preparation Specifications
Copper Tubing Roll Groove Specifications
| 1
Nom. | 2 Pipe Outside Diameter | 3 | 4 | 5 | 6 | 7 | 8 | |
| Dimensions - Inches/millimeters | ||||||||
| Basic | Tolerance | Gasket Seat A ±0.03 ±0.76 | Groove Width B ±0.03 ±0.76 | Groove Dia. C. +0.00 -0.02 | Groove Depth (ref.) D | Min. Allow. Wall Thick. T | Max. Allow. Flare Dia. | |
| 2 50 | 2.125 54.0 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 2.029 51.5 | 0.048 1.2 | 0.064 1.6 | 2.220 56.4 |
| 2 1/4 65 | 2.625 66.7 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 2.525 64.1 | 0.050 1.2 | 0.065 1.7 | 2.720 69.1 |
| 3 80 | 3.125 79.4 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 3.025 76.8 | 0.050 1.2 | DWV | 3.220 81.8 |
| 4 100 | 4.125 104.8 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 4.019 102.1 | 0.053 1.4 | DWV | 4.220 107.2 |
| 5 125 | 5.125 130.2 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 4.999 127.0 | 0.053 1.4 | DWV | 5.220 132.6 |
| 6 150 | 6.125 155.6 | ±0.002 ±0.05 | 0.610 15.5 | 0.300 7.6 | 5.999 152.3 | 0.063 1.6 | DWV | 6.220 158.0 |
| 8 200 | 8.125 206.4 | ±0.0004 ±0.08 | 0.610 15.5 | 0.300 7.6 | 7.959 202.2 | 0.083 2.1 | DWV | 8.220 208.6 |
COPPER TUBING ROLL GROOVE SPECIFICATIONS
COLUMN 1 - Nominal ASTM B-88 drawn copper tubing size
COLUMN 2 - Outside diameter: The outside diameter of roll grooved tubing shall not vary more than the
tolerance listed. The maximum allowable tolerance from square cut ends is 0.030" (0.8 mm) for 2 - 3" (50 - 80 mm);
0.045" (1.1 mm) for 4 - 6" (100 -150 mm), measured from true square line.
COLUMN 3 - Gasket seat: The tubing surface shall be free from indentations, roll marks, and projections from
the end of the tubing to the groove, to provide a leak-tight seat for the gasket. All loose scales, dirt, chips and
grease must be removed.
COLUMN 4 - Groove width: Bottom of groove to be free of loose dirt, chips and scale that may interfere with
proper coupling assembly.
COLUMN 5 - Groove outside diameter: The groove must be uniform depth for the entire tubing circumference.
Groove must be maintained within the "C" diameter tolerance listed.
COLUMN 6 - Groove depth: For reference only. Groove must conform to the groove diameter "C" listed.
COLUMN 7 - ASTM B-306 drain waste and vent (DWV) is minimum wall thickness copper tubing which may be
roll grooved.
COLUMN 8 - Maximum allowable end flare diameter: measured at the most extreme tubing end diameter.
Request 25.06