Victaulic Catalog

Pipe Preparation Specifications

Rigid Radius Cut Groove Specifications - Ductile Iron Pipe

1

 

Nom.
Size
Inches
mm

2

Pipe Outside Dia. O.D.
Inches/mm

34567
Dimensions - Inches/millimeters
BasicToleranceGasket
Seat
A+
+0.000
-0.020		Groove
Width
B
+0.031
-0.016		Groove Dia
C **		Radius
R		Min. Allow.
Wall Thick. T#
+-BasicTol.
+0.000		Cast
Iron		Ductile
Iron
3
80		3.96
100.6		+0.045
+1.14		-0.045
-1.14		0.840
21.34		0.375
9.53		3.723
94.56		-0.020
-0.51		0.120
3.05		0.32
8.1		0.31
7.9
4
100		4.80
121.9		+0.045
+1.14		-0.045
-1.14		0.840
21.34		0.375
9.53		4.563
115.90		-0.020
-0.51		0.120
3.05		0.35
8.9		0.32
8.1
6
150		6.90
175.3		+0.060
+1.52		-0.060
-1.52		0.840
21.34		0.375
9.53		6.656
169.06		-0.020
-0.51		0.120
3.05		0.38
9.7		0.34
8.6
8
200		9.05
229.9		+0.060
+1.52		-0.060
-1.52		0.950
24.13		0.500
12.70		8.781
223.04		-0.025
-0.64		0.145
3.68		0.41
10.4		0.36
9.1
10
250		11.10
281.9		+0.060
+1.52		-0.060
-1.52		1.015
25.78		0.500
12.70		10.813
274.65		-0.025
-0.64		0.145
3.68		0.44
11.9		0.38
9.7
12
300		13.20
335.3		+0.060
+1.52		-0.060
-1.52		1.015
25.78		0.500
12.70		12.906
327.81		-0.030
-0.76		0.145
3.68		0.48
12.2		0.40
10.2
14
350		15.30
388.6		+0.050
+1.27		-0.080
-2.03		1.015
25.78		0.625
15.88		14.969
380.21		-0.030
-0.76		0.165
4.19		0.55
14.7		0.42
10.7
16
400		17.40
442.0		+0.050
+1.27		-0.080
-2.03		1.340
34.04		0.625
15.88		17.063
433.40		-0.030
-0.76		0.165
4.19		0.58
14.0		0.43
10.9
18
450		19.50
495.3		+0.050
+1.27		-0.080
-2.03		1.340
34.04		0.625
15.88		19.125
485.78		-0.030
-0.76		0.185
4.70		0.63
16.0		0.44
11.2
20
500		21.60
548.6		+0.050
+1.27		-0.080
-2.03		1.340
34.04		0.625
15.88		21.219
538.96		-0.030
-0.76		0.185
4.70		0.67
17.0		0.45
11.4
24
600		25.80
655.3		+0.050
+1.27		-0.080
-2.03		1.340
34.04		0.625
15.88		25.406
645.31		-0.030
-0.76		0.185
4.70		0.73
18.5		0.47
11.9
30
750		32.00
812.8		+0.080
+2.03		-0.060
-1.52		1.625
41.28		0.750
19.05		31.550
801.37		-0.035
-0.89		0.215
5.46		0.92
23.4		0.51
13.0
36
900		38.30
972.8		+0.080
+2.03		-0.060
-1.52		1.625
41.28		0.750
19.05		37.850
961.39		-0.035
-0.89		0.215
5.46		1.02
25.9		0.58
14.7

+ Must be smooth and free of deep pits or swells.
** Groove must be uniform depth for entire pipe circumference. Groove must conform to "C" diameter shown.
* Ovality, or out-of-roundness, must lie within specified tolerances.
# Min. standard wall thickness that should be grooved. Tolerances are to conform to ANSI/AWWA C151/A21.51.
For 18-36" (450 - 950 mm) ductile iron Class 53 pipe may be used. Contact Victaulic for details.

Victaulic groove specifications for cast pipe (gray and ductile) conform to requirements of ANSI/AWWA standard C-606.
For cast pipe, the groove is cut with a radius ("R" dimension) at the comers of the groove base to reduce stress concentration. Grooving dimensions are the same for any one pipe O.D. regardless of pipe class and pressure.
Standard preparation is with a rigid radius groove. Flexible radius groove dimensions may be used to provide expansion/contraction or angular movement allowance at the joint.
The outside surface of the pipe between the groove and pipe end must be smooth and free from deep pits or swells to provide a leak-tight seat for the Victaulic gasket. All rust, loose scale, oil, grease and dirt shall be removed. Peened surfaces may require corrective action to provide leak-tight gasket seal (refer to ANSI/AWWA C-606).
Request 25.05 for Flexible and Rigid Radius Cut Groove Specifications.