Victaulic Catalog

IPS Carbon Steel Pipe
Fit System

FIT Outlet
Mechanical-T Cross

Nominal Size (IPS)Nominal Size (IPS)
Inches
RunBranchRunBranch
ABAB
3 xx 1 1/4
x 1 1/2
x 1 1/2		x 1 1/4
x 1 1/4
x 1 1/2		4xx 1 1/4
x 1 1/2
x 1 1/2		x 1 1/4
x 1 1/4
x 1 1/2
x 2
x 2
x 2		x 1 1/4
x 1 1/2
x 2		x 2
x 2
x 2

The FIT outlet Mechanical-T cross allows varied combinations of outlet sizes. Added flexibility for design andinstallation is an important feature.

Cross
Combinations

Nominal Size (IPS)
Inches		Nominal Size (IPS)
Inches
RunBranchRunBranch
ABAB
2 xx 1 1/4 FIT
x 1 1/4 FIT
x1 1/4 FIT		x 1 1/4 FIT
x 1 1/2 FIT
x 1 1/4 Thd		2 1/2 xx 1 1/4 FIT
x 1 1/4 FIT
x 1 1/4 FIT		x 1 1/4 FIT
x 1 1/2 FIT
x 1 1/4 Thd
x 1 1/4 FIT
x 1 1/4 Thd
x 1 1/4 Thd		x 1 1/2 Thd
x 1 1/4 Thd
x 1 1/2 Thd		x 1 1/4 FIT
x 1 1/4 Thd
x 1 1/4 Thd		x 1 1/2 Thd
x 1 1/4 Thd
x 1 1/2 Thd
x 1 1/2 FIT
x 1 1/2 FIT
x 1 1/2 FIT		x 1 1/2 FIT
x 1 1/2 Thd
x 1 1/4 Thd		x 1 1/2 FIT
x 1 1/2 FIT
x 1 1/2 FIT		x 1 1/2 FIT
x 1 1/2 Thd
x 1 1/4 Thd

Cross combinations of 2 and 2 1/2" (50 - 65 mm) sizes of Style 929 are available for cross-type connections. All sizes are available with FIT or female threaded ends.

NOTES

The following notes are applicable, except where noted, for Victaulic FIT products when Maximum End Load,Working Pressure and Dimensional data are listed.
* Refer to Pipe Tolerances for engaged pipe data** Center of run to engaged pipe end (Dimensions approximate)
§§ Center of run to end of fittings# Take-out dimensions
§ UL/ULC/FM working pressure based upon 5 to 1 test to rated pressure formula. Working Pressure and End Load are total, from all internal and external loads, based on steel pipe meeting FIT Pipe Tolerances (see table above) thoroughly cleaned to Victaulic FIT products specifications with all locking lugs in properly locked position.
WARNING: FOR ONE TIME FIELD TEST ONLY. the Maximum Joint Working Pressure may be increased to 1 1/2 times the figures shown.
WARNING: Piping systems must always be Repressurized and drained before attempting disassembly and removal of any Victaulic piping products.
This product shall be manufactured by Victaulic Company. All products to be installed in accordance with current Victaulic installation/assembly instructions.
Victaulic reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligations.