Victaulic Catalog

IPS Carbon Steel Pipe
Fire Protection Products

Style 735
Fire Pump Test Meter

Nom.
Size
In./mm		GPM
m3/hr.		End to
End
Inches
mm		Aprox. Wgt. Ea.Nom.
Size
In./mm		GPM
m3/hr.		End to
End
Inches
mm		Aprox. Wgt. Ea.
Model
"L"		Model
"S"		Model
"L"		Model
"S"
Lbs./kgLbs./kg
2 1/2
65		100
23		4.00
102		14.0
6.4		9.0
4.1		8
200		1500
341		7.00
178		27.0
12.3		22.0
10.0
3
80		200
45		4.25
108		15.0
6.8		10.0
4.5		8
200		2000
454		7.00
178		27.0
12.3		22.0
10.0
4
100		250
57		3.75
95		17.0
7.7		12.0
5.4		8
200		2500
568		7.00
178		27.0
12.3		22.0
10.0
4
100		300
68		3.75
95		17.0
7.7		12.0
5.4		8
200		3000
681		7.00
178		27.0
12.3		22.0
10.0
4
100		450
102		3.75
95		17.0
7.7		12.0
5.4		10
250		3500
795		8.00
203		38.0
17.2		33.0
15.0
5
125		500
114		5.00
127		18.0
8.2		13.0
5.9		10
250		4000
908		8.00
203		38.0
17.2		33.0
15.0
6
150		750
170		6.00
152		20.0
9.1		15.0
6.8		10
250		4500
1022		8.00
203		38.0
17.2		33.0
15.0
6
150		1000
227		6.00
152		20.0
9.1		15.0
6.8		12
300		5000
1135		12.00
305		71.0
32.2		66.0
29.9
6
150		1250
284		6.00
152		20.0
9.1		15.0
6.8

* Specify Model "L" for 6" dial; Model "S" for 4 1/2" dial.

The Style 735 Victaulic Fire Pump Test Meter was specifically designed for the monitoring of fire protection systems. Style 735 consists of a calibrated Victaulic Venturi with attached dial meter (specify Model "S", 41/2-/115mm dial meter; or Model "L", 6"/150 mm dial meter) and flow reading in GEM (gallons per minute) or MSS/ HR (cu.meters/hour). Quickly installed on the discharge side of the pump with just two Victaulic couplings, the Style 735 provides accurate measurements of pump performance.
The Victaulic Fire Pump Test Meter is designed for use with Victaulic FM Approved products in 21/2 through 12" (65 -300 mm) sizes. Maximum working pressure for Model "L" is 175 PSI (1200 kPa), Model "S" is rated to 500 PSI(3450 kPa).
Request 10.11.

Style 735
Installation

OPERATING INSTRUCTIONS FOR VICTAULIC FIRE PUMP FLOW VENTURI

  1. Close system valve "A".
  2. Open bypass valve and throttle valve "B".
  3. Purge meter located on Style 735 Fire Pump Test Meter as follows: Open station shut-off valves (below meter) and vent valves (above meter). When a steady stream of water is passing through each plastic hose, meter is purged of air. Close all valves after air purging.
  4. Start Fire Pump and read meter in GPM (M3/HR).
  5. Refer to pump GPM requirement and adjust throttle valve to achieve various flow readings. Record pump GPM, suction and discharge pressures, etc., accordance with requirements.